Grab 75% Off This Black Friday: Use coupon code below to save on all exam bundles! - Ends in 0d 00h 00m 00s - Coupon code: 75only

301a BIG-IP LTM Specialist: Architect, Setup, and Deploy (301a) Questions and Answers

Questions 4

Pool member forced offline for maintenance

An LTM Specialist works on a virtual server with a Source Address Affinity persistence profile. Maintenance is needed on one pool member. The specialist disables the member, but several hours later it still has active connections. What should the specialist do? (Choose one answer.)

Options:

A.

Change the pool Slow Ramp Time to zero

B.

Change Action on Service Down to Reject

C.

Change the pool-member state to Forced Offline

D.

Change the virtual server state to Disabled

Buy Now
Questions 5

A virtual server configuration for traffic destined to a server is as shown:

301a Question 5

FTP traffic is destined to the 192.168.1.101 server from the source of 192.168.2.129.

Based on precedence, which virtual server accepts this traffic?

Options:

A.

MyVS4

B.

MyV53

C.

MyVS1

D.

MyVS2

Buy Now
Questions 6

An organization’s development team creates an application to put behind the BIG-IP LTM device. The application can be quite load intensive at first, and then evens out over time. The team’s load balancing method needs to select a pool after taking into account the pool member’s response over the time to avoid landing on a busy pool member.

Which of the following load balancing methods meets this requirement?

Options:

A.

Fastest (application)

B.

Predictive (member)

C.

Dynamic (node)

D.

Observed (member)

Buy Now
Questions 7

A design requires the LTM device to become HA standby when the one of the two physical interface on the External trunk is down the External trunk is an interface on the External VLAN

Which TMOS command enables this behavior?

Options:

A.

tmsh modify net van External failsafe enabled

B.

tmsh create sys ha-group External trunks add Externally

C.

tmsh create sys ha-group External trunks add External threshold 2 weight 101)

D.

tmsh create sys ha-group External trunks add ( External( attribute percent up-members 100))

Buy Now
Questions 8

Intermediate certificate in Client SSL chain

A new SSL certificate is being installed for an existing web application. The certificate is signed by an intermediate CA, and that CA has provided the intermediate certificate. Which action should be taken? (Choose one answer.)

Options:

A.

Import the intermediate certificate and add it to the Trusted Certificate Authorities

B.

Import the intermediate certificate and add it to the Server SSL profile

C.

Import the intermediate certificate and add it to the Client SSL profile certificate chain

D.

Import the root CA certificate on the users’ desktops

Buy Now
Questions 9

Four members in a server pool have similar hardware platforms. An LTM Specialist needs the load balancing method that can select the server with the fewest entries in the persistence table.

Which load balancing method should the LTM Specialist use?

Options:

A.

Observed

B.

Dynamic Ratio

C.

Least Sessions

D.

Leas Connections

Pay attention to the examination questions, the stem is to ask the session to keep the minimum entries in the table.

Buy Now
Questions 10

MyVS matching with recovered client source

A virtual server configuration for traffic destined to a server is shown below. HTTP traffic is destined to server 10.10.20.1 from source 10.10.10.129. Based on precedence, which virtual server accepts this traffic?

Exhibit — VS Name | Destination | Service port | Source

MyVS1 | 10.10.20.1/32 | 80 | 0.0.0.0/0

MyVS2 | 10.10.20.1/32 | * | 10.10.10.0/24

MyVS3 | 10.10.20.1/32 | 80 | 10.10.10.0/25

MyVS4 | 10.10.20.0/24 | 21 | 0.0.0.0/0

(Choose one answer.)

Options:

A.

MyVS1

B.

MyVS3

C.

MyVS2

D.

MyVS4

Buy Now
Questions 11

Exhibit.

301a Question 11

An LTM Specialist needs to configure VS^HTTP and VS_DB for an online shopping site. The VS HTTP passes the client requests to the webservers. The webservers query the database servers through the VS_DB. Initially, the LTM Specialist finds the database servers directly return the packets to the webservers.

which setting must be enabled for the configuration to function correctly?

Options:

A.

VS_HTTP snat auto map

B.

VS.HTTP auto last hop

C.

VS DB auto last hop

D.

VS_DB snat auto map

Buy Now
Questions 12

An LTM Specialist needs to configure a virtual server with the requirements displayed below.

Application is currently an internal HTTP application

Encrypted external user access

Links are hard for siteA example.com and need to rewritten to siteB.Example.com

Which profiles must the LTM Specialist use to provide the proper functionality?

Options:

A.

Clientssll, Stream

B.

Serverless, Stream

C.

Clientssl, fastL4, Stream

D.

Serverless, fastL4, Stream

For http application and external encryption, clientssl is required, and if the message content needs to be modified, the steam profile is required. FastL4 profile cannot coexist with clientssl and stream.

Buy Now
Questions 13

An LTM Specialist reports that an application si no longer reachable after it has been upgraded.

Nothing has been changed in the configuration on the LTM device.

The logs indicates that health monitors to all servers have failed as shown:

What should the LTM Specialist verify next?

Options:

A.

That the TCP hand shake with the servers is stall completed using tcpdump

B.

That the custom receive string for the HTTP monitor has changed with the upgrade

C.

That the can still ping the servers from te BIG_ IP device.

D.

That the firewall between the BIG-ip device and servers is still allowing HTTP

The log shows that tcp detection is normal, but http detection is abnormal. So we should pay attention to the detection problem of http level

Buy Now
Questions 14

High CPU with connection mirroring

A BIG-IP LTM device is configured for many HTTP virtual servers. The LTM Specialist notices significant degradation of CPU performance. Which setting should the LTM Specialist modify to mitigate this concern? (Choose one answer.)

Options:

A.

Source Address Persistence

B.

Connection Limit

C.

SNAT

D.

Connection Mirroring

Buy Now
Questions 15

AN LTM Specialist is deploying an iRule designed to determine the country of origin of an incoming client connection. The iRule needs to be used with an SSL-enabled web application.

Which profile required for the iRule to function properly?

Options:

A.

HTTP

B.

DNS

C.

TCP

D.

UDP

Question stem requires the client IP to match the source region, so TCP ?UDP at the transport layer can meet the requirements. The title stem mentions that it is a Web application based on SSL, and it does not mention F5 undertakes SSL offload, So TCP is enough.

Buy Now
Questions 16

RADIUS authentication has been configured on the LTM device. The default remote user access requirements are as shown:

Read only access to the configuration Utility

Access to TMOS shell

Which two items need to be configured in this situation? (Choose two)

Options:

A.

Console access is Advanced Shell

B.

Console access is Read Only

C.

Default remote user role is Guest

D.

In Console access is TMSH

E.

Default remote user role is Manager

F.

Default remote user role is Operator

Buy Now
Questions 17

What should an LTM Specialist configure on an LTM device to send AVR notification emails?

Options:

A.

Email notification to be sent via iControl from the LTM device

B.

Syslog on the LTM device to send to an SMTP server

C.

Custom SNMP traps on the LTM device for AVR notifications

D.

Email notification to be sent via SMTP from the LTM device

Buy Now
Questions 18

TWO LTM devices are in the same Device Group and configured for Ac live/Standby Failover. The LTM Specialist observes that the HA Active and Standby device constantly changes state. All network links use the default route domain A dedicated fiber ink is used for the HA connection with a latency of 250 ms but no packet loss.

301a Question 18

What is causing the change in failover state to occur?

Options:

A.

The HA network is using the default routing domain.

B.

The HA network is using multicast IP.

C.

The HA network is not configured for mirroring.

D.

The HA network latency is too high.

Buy Now
Questions 19

A virtual server with SNAT automap enabled selects pool member 10.20.0.10.443 for the server-side flow. The client side flow source IP is 192.168.0.10 .

301a Question 19

Which source IP should be expected in the server-side connection?

Options:

A.

10.20.0.1

B.

10.50.0.2

C.

10.20.0.2

D.

192.168.0.10

Buy Now
Questions 20

An LTM Specialist needs to deploy a virtual server that will load balance traffic targeting https://register.example.com to a set of three web servers. Persistence needs to be ensured. No persistence mirroring is allowed SSL offloading is required.

A fourth web server with fewer resources will be used to handle requests from engine bots to https://register.example.comvrobots.txt by an iRule. The (Rule will use the HTTP_REQUEST event. .

What are the required profile and persistence settings to implement this

Options:

A.

tcp. dientssl, hup, source address persistence

B.

tcp, clientssl, http. cookie persistence

C.

tcp, clientssl, serverssl, ssl persistence

D.

tcp, clientssl, http, serverssl cookie persistence

The option is wrong, it should be clientssl and serverssl. If the title requires ssl offload instead of encryption, you need clientssl instead of serverssl. irule needs HTTP profile to enable HTTP_REQU£ST. If

the session cannot be mirrored, the cookie session remains to meet the demand.

Buy Now
Questions 21

Block unwanted admin source by packet filter

An unwanted IP address tries to connect to the Configuration utility through a Self IP. An LTM Specialist needs to block the attempts based on the IP address without affecting other users. How should the LTM Specialist block the attempts? (Choose one answer.)

Options:

A.

Packet filter

B.

Device trust

C.

SSH IP allow list

D.

Port Lockdown

Buy Now
Questions 22

A new web application is being deployed Mutual SSL authentication must be used to authenticate clients.

Which of the following two tasks must be completed to meet the requirements? (Choose two)

Options:

A.

configure the server SSL profile with " Client Certificate " Set to require

B.

configure the client SSL profile with " Client Certificate " set to require

C.

instruct the desktop team to update the web browser to the most recent release

D.

generate a CSR to register a certificate with the CA

E.

configure the client SSL profile with the Trusted .Certificate Authorities

Buy Now
Questions 23

While working with a web developer, it is determined that additional logic is required to assess the pool member availability.

Which two monitor types should be used in this scenario? (Choose two)

Options:

A.

TCP

B.

Scripted

C.

Gateway ICMP

D.

TCP Echo

E.

External

Buy Now
Questions 24

An LTM Specialist needs to configure a setup for antivirus scanning of HTTP traffic with an internet Contact adaption Protocol (ICAP) server.

Which two server type should be used? (Choose two.)

Options:

A.

Standard

B.

Internal

C.

Performance HTTP

D.

Forwarding IP

E.

Stateless

Buy Now
Questions 25

Exhibit.

301a Question 25

The server team has recently configured the three new DNS servers shown for the data center. No current DNS servers are currently configured on the LTM device.

Which command should be used to configure the LTM device to use the new DNS servers?

Options:

A.

tmsh create/systins name-servers add {192 168.1.2.192.168.100.1O0.192.168.2O0.2OO}

B.

tmsh change /sysdns name-servers add {192.168.1.2.192.168.100.100.192.168.200.200}

C.

tmsh modify/sysdns name-servers add {192.168.1.2.192.168.100.100.192.168.200.200}

D.

tmsh set/sysdns name-servers add {192.168.2.192.168.100.100.192.168.200.200}

Modify the configuration with modify, and create the configuration with create. Excluding B and D, and the question is to modify the DNS pointer of E5 itself the need to use is modify.

Buy Now
Questions 26

Refer to the exhibit.

301a Question 26

A pool is contoured with four members. A user has a current connection established with 10.18.1.40. The virtual server has a persistence Profile configured.

Options:

A.

10.18.1.10

B.

10.18.1.20

C.

10.18.1.40

D.

10.18.1.30

Buy Now
Questions 27

An LTM Specialist is removing some of the load off an existing cluster by adding a adding a third BIG-IP

device to the device group. The new device can deliver twice the performance of the other two devices.

The LTM Specialist needs to make sure that the BIG-IP device with the highest available capacity is

always selected to take over a traffic group in the event of a failover.

Which failover method is most appropriate?

Options:

A.

Ordered List

B.

Load Aware

C.

HA Group

D.

HA Capacity

Buy Now
Questions 28

An LTM Specialist needs to provide statistics regarding the round-trip time between the clients and the servers.

Which metric should be part of the analytics profile to provide that information?

Options:

A.

Page Load Time

B.

User Sessions

C.

Max TPS and Throughout

D.

Response Codes

Buy Now
Questions 29

An LTM is configure an application that is separated into several subdomains across multiple virtual servers. Many of these subdomains require encryption and could be accessed by anyone on the internet. The configuration must NOT result in SSL warnings to end users.

How should the LTM Specialist configure the SSL profiles for these virtual servers?

Options:

A.

Obtain an SSL certificate for each subdomain, make a ServerSSL profile for each subdomain, and apply to the related SSL Virtual Server.

B.

Obtain a wildcard certificate, create one ClientSSL profile and apply to all SSL Virtual Servers

C.

Create a self-singed SSL certificate for each subdomain make a ClientSSL profile for each subdomain, and apply to the related SSL Virtual server

D.

Create a self-singed SSL certificate for each subdomain make a Client profile for each SSL Virtual Server

Technical note: A publicly trusted certificate and Client SSL profile are required; the wildcard option applies only to DNS names within the certificate scope.

Buy Now
Questions 30

A virtual server is configured to handle https traffic. The clientssl profile is configured to use a 2048-bit RSA key. Due to security requirements, is the LTM Specialist needs to use a 4096-bit RSA key in the future.

What two effects will this change have on the BIG-IP device? (Choose two)

Options:

A.

Increase of CPU usage on the BIG-IP device

B.

Decrease to 20% of licensed TPS

C.

Decrease to 90% of licensed TPS

D.

Increased of concurrent connection on client-side

E.

Increase of TLS Renegotiation

Buy Now
Questions 31

TCP monitors: service and shared dependency

An LTM Specialist needs to assign health monitors to a pool with two members, 10.10.10.101 and 10.10.10.102, both listening on TCP port 8080. Application health also depends on another server at 10.10.10.100 listening on TCP port 9080. Which two custom TCP monitors should be selected? (Choose two answers.)

Options:

A.

A custom TCP monitor on port 9080 with 10.10.10.100 as alias address

B.

A custom TCP monitor on port 9080

C.

A custom TCP monitor on port 8080

D.

A custom TCP monitor on port 8080 with 10.10.10.101 as alias address

E.

A custom TCP monitor on port 8080 with 10.10.10.102 as alias address

F.

A custom TCP monitor on port 9080 with 10.10.10.101 as alias address

Buy Now
Questions 32

An application is being load balanced through the LTM device using the configuration displayed below.

The network has been re-engineered to NAT all client connection. As a result, all client connections are hitting the same pool member.

301a Question 32

Which changes should the LTM Specialist make in order to restore load balancing functionality wile maintaining session persistence?

Options:

A.

Change the virtual server type to Standard, add an http profile, and change the persistence profile to Destination Address

B.

Leave the virtual server type set Performance (Layer 4) and change the persistence type to hash

C.

Change the virtual serer type to Forwarding (Layer 4) and leave the persistence type to hash source Address

D.

Change the virtual server to Standard add an http profile, and change the persistence profile to Cookie persistence

Buy Now
Questions 33

in which Application Visibility and Reporting (AVR) profile must the SMTP profile be defined to configure notifications via email?

Options:

A.

App analytics profile

B.

virtual server profile

C.

custom analytics profile

D.

default analytics profile

Buy Now
Questions 34

An application is expected to maintain more than 100,000 concurrent TCP connections to a single pool member.

What is an appropriate SNAT configuration in this situation?

Options:

A.

A SNAT pool with 4 IP addresses

B.

SNAT automap enabled

C.

A static SNAT

D.

A SNAT pool with IP address

Explanation

One IP can establish 65,535 connections only the number of snapit’s IP exceeds 100,000. AT least two snaptips are required. Options B, C, and all have only IP, which is obviously not enough

Buy Now
Questions 35

A custom TCP application using a single server is being migrated to the LTM device. A server is being added to the pool. The application is known to violate the TCP protocol RFC. The application currently works without error from a user perspective.

Which virtual server type is appropriate in this situation?

Options:

A.

Stateless TCP protocol is not applicable

B.

Performance (Layer 4)-pure layer A forwarding

C.

forwarding (Layer 2) pure routing forwarding, pool cannot be specified

D.

Standard-tcp profile exists, RFC verification will be performed

Buy Now
Questions 36

An LTM Administrator receives an email from the NOC stating that the switch connected to the backend server was shut down for maintenance. The BIG-IP device handles only UDP traffic. The BIG-IP device did not fail over to a DR location when no pool members were available.

When the LTM Administrator checks the pool, it confirms that the monitor is still marking UP the pool member.

A tcpdump of the traffic shows the following output:

301a Question 36

A list of the monitor configuration shows the following:

Which two modifications to the LTM configuration will mark this pool member down, when the switch is down? (Choose two.)

Options:

A.

increase the timeout to three times the interval

B.

add a reverse string to the game monitor

C.

enable reverse and wait for the next connection

D.

also assign a gatewayjcmp monitor to the pool

E.

enable manuai-resume on the same monitor

Buy Now
Questions 37

Refer to the following iRule:

301a Question 37

What is a complete list of profiles that must be applied to the virtual server for this iRule?

Options:

A.

Fast L4, HTTP

B.

TCP, HTTP

C.

TCP, HTTP, Client SSL

D.

Fast L4 , HTTP, Stream

Buy Now
Questions 38

An LTM Specialist needs to create two virtual servers.

The application has links for both HTTP and HTTPS version of application. The client must be persistence to a pool member, no matter which virtual server is accessed.

What must be selected in the Source Address Affinity persistence profile?

Options:

A.

Match across Virtual Servers

B.

Match across Pool Members

C.

Match across Services

D.

Match across Polls

Buy Now
Questions 39

Refer to the exhibit.

301a Question 39

The pool shown is configured with four pool members in a variety of states. The application is receiving a large number of request. The LTM Specialist needs to make changes to make sure that all members receive the same levels of traffic.

Which changes need to be made?

Options:

A.

Enable 10.80.1.40 disable priority group activation, enable ratio

B.

Enable 10.80.1.40 and 10.80.1.1.20 disable group activation, enable Round Robin

C.

Enable 10.80.1.20 disable priority group activation, enable Round Robin

D.

Enable 10.80.1.40 and 10.80.1.20 disable priority group activation, enable ratio.

Buy Now
Questions 40

A pool has four members. Ail of the servers have been designed and configured with the same application. Each client ' s request can significantly the performance of the servers.

Which load balancing method should the LTM Specialist use to maintain a relatively even load across all servers?

Options:

A.

Least Connections

B.

Priority Group

C.

Ratio

D.

Observed

Buy Now
Questions 41

An LTM device needs an additional traffic group.

Which configuration item is required?

Options:

A.

Default device

B.

Group name

C.

MAC Masquerade Address

D.

Auto Fallback Timeout

Buy Now
Questions 42

A new DNS virtual server has been configured. Testing reveals that DNS server has failed to accept DNS over TCP. The configuration of the virtual server is as follows:

301a Question 42

Which action should be taken to correct this issue?

Options:

A.

create a new virtual server with the service port of 53 and the protocol set to TC

B.

change the profile set on the virtual server To TCP/UDP

C.

change the profile set on the virtual server to TCP

D.

add a TCP prone to the existing virtual server.

Buy Now
Questions 43

An LTM Specialist discovers an issue with the custom http monitor that returns in a false positive status.

The end users cannot get the right website, but the http monitor marks the pool member UP.

What is causing the false positive result?

301a Question 43

Options:

A.

The end user should use another type of browser.

B.

The response is chunked.

C.

The response is compressed.

D.

The Content-Type has value " iso-8859-200 " .

Buy Now
Questions 44

Refer to the exhibit.

301a Question 44

An LTM Specialist configures the two syslog destination Syslog destination #1 can receive messages but the syslog destination #2 can NOT receive messages.

Which command sill correct the issue?

Options:

A.

{/Common)(tmos) # modify /syssyslog remote-servers modify (syslog_dest2 {local-ip

B.

{/Common)(tmos) # modify Ays syslog remote servers modify {syslog_dest2 {local- ip 10.208.102 254)}

C.

{/Common) (tmos) # modify /sys syslog remote-servers modify {syslog_dest2 {host 10 208.102.254 }}

D.

{Common(tmos) # modify/syslog remote-servers modify {syslog_dest2 {lost.10.10.10.28 }}

Buy Now
Questions 45

The web application team requests help from the LTM Specialist to Improve the performance of their web sites that are load balanced by the BIG-IP LTM device with a Standard Virtual Server.

Which virtual server type will improve the performance of the web application servers?

Options:

A.

Performance (HTTP)

B.

Performance (Layer 4)

C.

Stateless

D.

Forwarding (IP)

Buy Now
Questions 46

Forwarding virtual server exposes other ports

An LTM Specialist must create a new virtual server for HTTP access. The LTM Specialist creates a Forwarding virtual server to reach the resource. What is a potential result of this action? (Choose one answer.)

Options:

A.

Other service ports could be allowed

B.

HTTP traffic is not allowed

C.

IP conflicts result

D.

Packet filter allowances are also required

Buy Now
Questions 47

Node with ICMP and TCP monitors

A node is assigned two monitors. A packet capture shows ICMP echo requests and replies with 10.128.20.12, an HTTP TCP connection receiving a reset, and an HTTPS TCP connection that successfully establishes to 10.128.20.12:443. What is the status of a pool member running on that node and listening on port 443? (Choose one answer.)

Options:

A.

Unavailable

B.

Up

C.

Unknown

D.

Down

Buy Now
Questions 48

A company plans to launch a huge marketing campaign and expects increase demand of their secure website. With the current virtual server setup, the LTM Specialist expects that the LTM device will reach its capacity limits. For the wen application to function properly. Cookies persistence is required. The LTM Specialist needs to reduce LTM device load without breaking the application.

Which two settings should the LTM Specialist modify to meet the requirement? (Choose two.)

Options:

A.

Remove HTTP compression profile

B.

Remove HTTP profile

C.

Remove web acceleration profile.

D.

Modify virtual Server type to performance (Layer 4)

E.

Remove ClientSSL profile

It is required that cookie persist must be used and http profile must be used, and SSL offloading must also be required. It must be in standard mode, excluding BD E.

Buy Now
Questions 49

HA group external trunk failure threshold

A design requires the LTM device to become HA Standby when one of the two physical interfaces on the External trunk is down. The External trunk is an interface on the External VLAN. Which TMOS command enables this behaviour? (Choose one answer.)

Options:

A.

tmsh create sys ha-group External trunks add { External }

B.

tmsh modify net vlan External failsafe enabled

C.

tmsh create sys ha-group External trunks add { External attribute percent-up-members 100 }

D.

tmsh create sys ha-group External trunks add { External threshold 2 weight 101 }

Buy Now
Questions 50

Exhibit.

301a Question 50

The three VLANS shown provide connectivity to backend servers. The backend servers are being moved to unmanaged switches and require separate interfaces.

How should the F5 device interfaces be configured?

Options:

A.

Create a Trunk interface and combined interface 1.1.1.2 and 1.3.

B.

Create a Trunk interface and select VLAN„A, VLAN_B. and VLAN_C.

C.

Create VLAN named VLAN_A enter 100 under Tag and move interface 1.1 to tagged Create VLAN_B enter 200 and move interface 1.2 to tagged Create VLAN_C Center 300 and move interface 1.3 to tagged.

D.

Create VLAN_A move interface 1.1 to untagged. Create VLAN_B move interface 1.2 to untagged. Create VLAN_C move interface 1.3 to untagged.

Buy Now
Questions 51

An LTM device configuration is as shown:

An LTM device configuration is as shown

301a Question 51

What should be the two expected outcomes based on this configuration? (Choose two.)

Options:

A.

A client session that has been idle for 16 minutes will be sent to the same pool member

B.

A client session that has been idle for 20 minutes will be balanced to a new pool member

C.

A client session that has been idle for 14 minutes will be balanced to a new pool member

D.

A client session that has been idle for 48 minutes will be sent to the same pool members

E.

A client session that has been idle for 12 minutes will be sent to the same pool member

Buy Now
Questions 52

A BIG-IP device delivers the online shopping website https://shop.example.com. Two pool members handle the traffic. An iRule directs requests with the hip parameter " environment=development " to a third pool member for a staging environment.

Which combination of profiles is needed at minimum?

Options:

A.

tcp, http, request logging

B.

tcp, http, clientssl

C.

tcp, clientssl, serverssl

D.

http, clientssl, persistence

Buy Now
Questions 53

New remote syslog via TMSH

The network team has recently added a new syslog server with IP address 10.1.1.12. Which command adds the new syslog entry on the F5 LTM device? (Choose one answer.)

Options:

A.

`tmsh modify sys syslog remote-servers add { server { host 10.1.1.1 remote-port 514 } } save sys config`

B.

`tmsh adjust sys syslog remote-servers add { server { host 10.1.1.1 remote-port 514 } } save sys config`

C.

`tmsh add sys syslog remote-servers add { server { host 10.1.1.1 remote-port 514 } } save sys config`

D.

`tmsh create sys syslog remote-servers add { server { host 10.1.1.1 remote-port 514 } } save sys config`

Buy Now
Questions 54

An LI M device is experiencing a high volume of traffic. The virtual server is struggling under the load. The problem appears to be on the server side connections. The virtual server is accepting connections . The virtual server is accepting connections on https and is configured with an SSL profile and http pool.

What should be added to increase the performance of the device?

Options:

A.

an HTTP Compression profile

B.

a One Connect profile

C.

smaller key to the SSL profile

D.

a SPDY profile

Buy Now
Questions 55

Import guest upgrade images to both vCMP hosts

An LTM Specialist must upgrade a vCMP Guest Active/Standby LTM pair from version 11.3 to 11.5.3 on two vCMP hosts. Where should the LTM Specialist import the 11.5.3 ISO images? (Choose one answer.)

Options:

A.

To both vCMP hosts

B.

To the primary vCMP host and the active guest instance

C.

To the secondary vCMP host and the standby guest instance

D.

To the vCMP guest instances

Buy Now
Questions 56

Client SSL optional certificate request

To improve application security, an LTM Specialist must configure BIG-IP to authenticate a client certificate before allowing application access. BIG-IP must also support redirecting users to a certificate-enrollment system without a browser TLS error. Which Client Certificate setting should be used in the Client SSL profile? (Choose one answer.)

Options:

A.

Require

B.

Demand

C.

Ignore

D.

Request

Buy Now
Exam Code: 301a
Exam Name: BIG-IP LTM Specialist: Architect, Setup, and Deploy (301a)
Last Update: Nov 21, 2026
Questions: 189

PDF + Testing Engine

$42.5  $169.99

Testing Engine

$32.5  $129.99
buy now 301a testing engine

PDF (Q&A)

$27.5  $109.99
buy now 301a pdf
dumpsmate guaranteed to pass

24/7 Customer Support

DumpsMate's team of experts is always available to respond your queries on exam preparation. Get professional answers on any topic of the certification syllabus. Our experts will thoroughly satisfy you.

Site Secure

mcafee secure

TESTED 21 Nov 2026