NFPA CFPS Exam Dumps - Actual Questions Answers

valve at the inspector’s test connection.

For wet-pipe automatic sprinkler systems, the only proper way to test the operation of a vane-type water flow alarm initiating device is to open the valve at the inspector’s test connection. This is a small valve that is located at the end of a pipe that is connected to the sprinkler system, usually at the most remote or highest point. The inspector’s test connection simulates the flow of a single sprinkler head and activates the vane-type water flow switch, which in turn triggers the fire alarm panel and the external alarm devices.Opening the valve at the inspector’s test connection also allows the water to drain from the system, preventing corrosion and freezing1234

Opening the main (2 in. diameter) drain is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not create enough flow to activate the switch. The main drain is used to drain the entire sprinkler system for maintenance or repair purposes, and it is usually located at the main riser or the fire department connection.Opening the main drain may also cause a pressure drop in the system, which could affect the performance of the sprinklers1234

Opening the alarm test by-pass valve at the system’s main riser is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not simulate the actual flow of a sprinkler head. The alarm test by-pass valve is used to test the operation of the external alarm devices, such as the water motor gong or the electric bell, without activating the fire alarm panel. The alarm test by-pass valve is usually located near the alarm check valve or the water flow switch, and it allows water to flow through a small orifice to the alarm devices.Opening the alarm test by-pass valve does not create enough flow to activate the vane-type water flow switch1234

Opening the check valve from the city connection is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not create any flow in the sprinkler system. The check valve from the city connection is used to prevent the backflow of water from the sprinkler system to the city water supply, and it is usually located at the fire department connection or the main riser.Opening the check valvefrom the city connection does not affect the water flow in the sprinkler system, and it does not activate the vane-type water flow switch1234

References:

• Fire Sprinkler Flow Switch & Tamper Switch Inspection & Maintenance3
• Sprinkler System Water Flow Device Testing - ORR Protection2
• VSR-AT Auto-Test Waterflow Alarm Switch | Potter Electric4
• WFDNA Series Vane-type Waterflow Detectors - Steel Fire Equipment5

According to NFPA 13, Table 17.4.2.1 (a), the maximum distance between hangers for an automatic fire sprinkler system for a threaded lightwall steel pipe of 2 in. diameter is 10 ft. This is done to ensure that there are not long stretches of unsecured piping that could sag, leak, or break. The distance between hangers may vary depending on the type of pipe, the type of hanger, and the seismic design category of the building.References:NFPA 13, Table 17.4.2.1 (a);Hangers and Support of Sprinkler System Piping | NFPA | NFPA.

NFPA 70, National Electrical Code (NEC), is the NFPA standard that governs wiring of a fire alarm system. NFPA 70 covers the general requirements for the design, installation, and inspection of electrical wiring and equipment, including fire alarm circuits anddevices. NFPA 70 does not cover the performance of a fire alarm system, which is addressed by NFPA 72, National Fire Alarm and Signaling Code. NFPA 72 covers the application, installation, location, performance, inspection, testing, and maintenance of fire alarm systems and their components. NFPA 73, NFPA 75, and NFPA 76 are other NFPA standards that are related to fire alarm systems, but they do not specifically govern wiring. NFPA 73 covers the electrical inspection of existing dwellings. NFPA 75 covers the protection of information technology equipment. NFPA 76 covers the fire protection of telecommunications facilities.References:

• NFPA 72 FAQs1
• National Fire Alarm and Signaling Code® - NFPA2
• TECHNICAL SERVICES DEPARTMENT BULLETIN - NEMA3