Juniper JN0-650 Exam Dumps - Actual Questions Answers

In an EVPN-VXLAN architecture, the network is divided into two distinct planes: the Underlay and the Overlay.

Underlay (IP Fabric): The underlay ' s only job is to provide IP reachability between the loopback addresses of all VTEPs (Virtual Tunnel Endpoints). This is typically achieved using OSPF, IS-IS, or EBGP.

Overlay (EVPN Control Plane): The overlay is responsible for carrying Layer 2 MAC and Layer 3 IP reachability information between switches. EVPN signaling is the standard mechanism for this task.

Protocol Choice (Option D): EVPN uses MP-BGP (Multiprotocol BGP) as its control plane protocol. On Juniper EX Series and QFX Series switches, the most scalable and recommended design for the overlay is EBGP (External BGP).

In a 3-stage or 5-stage Clos architecture, EBGP is used in the overlay to exchange EVPN routes (Route Types 1-5) between Leaf and Spine switches.

EBGP simplifies configuration by avoiding the need for Route Reflectors (required for IBGP) and provides better control over route propagation through BGP community and policy management.

Incorrect Options:

Options A and B refer to the underlay protocols. While they provide the path for the VXLAN tunnels, they do not handle the EVPN signaling itself.

Option C (MPLS) is a different transport technology. While EVPN can run over MPLS (EVPN-MPLS), campus designs on EX series devices specifically use VXLAN as the data plane, making EBGP the standard signaling protocol for the EVPN-VXLAN overlay.

OSPFv2 (IPv4) and OSPFv3 (IPv6) share many fundamental concepts, such as the SPF algorithm and the use of areas, but they have distinct differences in how they handle prefix information and LSA headers in Junos OS.

Backbone Requirement (Option C): Both OSPFv2 and OSPFv3 utilize a hierarchical structure. In both versions, all areas must connect to a central Area 0 (the backbone) to allow for inter-area routing. If an area is not physically connected to Area 0, a virtual link must be established.

Flooding Scope (Option D): One of the significant architectural changes in OSPFv3 is the inclusion of the flooding scope directly into the LSA header. In OSPFv3, the LS Type field is expanded to 16 bits, where the top three bits define the flooding scope (e.g., Link-local, Area, or AS scope). This allows routers to understand how far an LSA should be propagated without needing to understand the specific LSA type itself.

LSA Prefix Information (Option A): This statement is misleading. In OSPFv2, Router and Network LSAs (Type 1 and 2) carry both topology and prefix information. However, a key design goal of OSPFv3 was to separate topology from prefix information. In OSPFv3, Type 1 and 2 LSAs only describe the topology, while prefixes are carried in new LSA types: Intra-Area-Prefix-LSAs (Type 9) and Link-LSAs (Type 8).

Processing (Option B): OSPFv2 is processed " per-subnet " because it forms adjacencies based on IPv4 subnets. OSPFv3 is processed " per-link " , meaning it forms adjacencies between interfaces on the same physical link regardless of whether they share a common IPv6 prefix.

OSPF stub areas are used to reduce the size of the Link-State Database (LSDB) in routers with limited resources by restricting the flooding of external routes.

Virtual Links (Option C): According to OSPF standards (both v2 and v3), virtual links cannot pass through stub areas. A virtual link must transit a " transit area, " which must be a standard (non-stub) area with a full routing table.

Totally Stubby Areas (Option D): A stub area (which blocks Type 5 External LSAs) can be further restricted into a totally stubby area. In Junos OS, this is done by adding the no-summaries statement to the stub configuration. This blocks both Type 5 and Type 3 (Inter-area) LSAs, replacing them with a single default route.

Incorrect Statements: Option A is incorrect because standard stub areas cannot contain an ASBR; only Not-So-Stubby Areas (NSSA) allow for an ASBR. Option B is incorrect because an area is either a Stub or an NSSA; they are mutually exclusive configurations for the same area.