350-501 Implementing and Operating Cisco Service Provider Network Core Technologies (350-501 SPCOR) Questions and Answers

 To prevent packets from being forwarded beyond the service provider domain when the Label Switched Path (LSP) is down, the engineer must configure a private IP address as the destination address of the headend router of Cisco MPLS Traffic Engineering (TE). This ensures that if the LSP fails, the packets will not be routable over the public internet, thus containing them within the service provider’s network.

References := Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) documentation provides guidelines on MPLS TE configuration, including the use of private IP addresses for headend routers to maintain traffic within the service provider domain. This practice is aligned with the principles of traffic engineering and network containment for service providers.

Option B is the correct answer because it meets all the given requirements. The configuration “snmp-server community comaccess ro 10” allows read-only access for all objects to members of Access-List 10 that use the comaccess community string. The “snmp-server host ABC.com informs version 2c public” command ensures SNMP authentication failure traps are sent to SNMPv2c and then to the host using SNMPv2c with the public community string.

 The router RA is configured with the command “ip pim ssm default”. This configuration enables Source-Specific Multicast (SSM) for the default range of 232.0.0.0/8, which is the IPv4 multicast address space reserved for SSM by IANA (Internet Assigned Numbers Authority). In SSM, data traffic is delivered to a specific group of subscribers identified by the combination of both source and multicast addresses, enhancing efficiency and security. References: Implementing and Operating Cisco Service Provider Network Core Technologies

• Configure an IP domain name: An IP domain name is essential for generating RSA keys needed for SSH. The RSA keys are part of the crypto key configuration, which is necessary to enable SSH on the router. This step ensures that users are authenticated via the SSH protocol when accessing the network remotely.
• Configure crypto keys: The crypto keys are crucial for secure communication. The engineer should generate RSA keys using the configured IP domain name. These keys will be used for encryption and authentication during SSH sessions.

The other options (B, D, and E) are not directly related to completing the SSH configuration for secure remote access. Therefore, the correct answers are A and C.

References:

• Implementing and Operating Cisco Service Provider Network Core Technologies

To reduce network usage and minimize leave latency for users connected to VLAN 76, the configurations should focus on efficient multicast traffic management. Option A likely involves enabling IPv6 MLD snooping, which restricts multicast traffic to only the ports that have members interested in receiving the traffic, thus reducing unnecessary network usage. Option C might include configuring fast-leave processing, which allows the switch to immediately stop forwarding multicast traffic to a port when the last member of a multicast group leaves, reducing leave latency.

References := Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)

The correct configuration for PE1 to connect AS 200 of the service provider with AS 100 of enterprise ABC using BGP, considering the VRF RT 100:10 is already configured, would involve setting up BGP with the correct neighbor and route distinguisher settings. Option C is likely the correct choice as it specifies the BGP neighbor to be within the enterprise ABC’s AS 100 and includes the address family configuration necessary for VRF-aware BGP sessions. References := The Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials provide detailed instructions on configuring BGP in a service provider environment, including the use of VRFs and route distinguishers. For more information, please refer to the official Cisco documentation and course materials related to SPCOR1.

The QoS-group keyword on Cisco IOS XR is used for marking packets on the ingress of the device. This allows for internal handling and is not transmitted across the network. It can be used in fabric QoS policy as a match criteria to apply specific policies based on the QoS group marking.

References: = Implementing and Operating Cisco Service Provider Network Core Technologies course materials. 

The issue with establishing an IS-IS adjacency between the two routers stems from a mismatch in the configuration of their interfaces. Router R2’s interface is set to point-to-point, while the peer router interface is set to multipoint. For IS-IS adjacencies to form, both interfaces must be configured with the same network type. The discrepancy in the network types is preventing the adjacency from being established. To resolve this, the network operator must ensure that both interfaces are either configured as point-to-point or as multipoint. References := Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)

Network Services Orchestrator (NSO) uses the YANG (Yet Another Next Generation) modeling language to provide a standardized way to automate network devices. YANG provides a powerful schema to model configuration and state data for network elements, which NSO leverages for service automation and orchestration.

References: Cisco Crosswork Network Services Orchestrator (NSO) - Cisco2.

 In Cisco IOS XR software, the keychain management for BGP is done in the routing configuration mode. This mode allows you to configure keychain parameters such as the key identifier, cryptographic algorithm, and other related settings. The keychain is essential for authentication and secure communication between BGP peers. By configuring the keychain in the routing context, you ensure that BGP sessions use the specified keys for authentication and integrity protection1.

References:

• Implementing Keychain Management - Cisco IOS XR Routing Configuration Guide
• BGP Configuration Guide for Cisco NCS 540 Series Routers, IOS XR Release 7.8.x - Master Key Tuple Configuration

During the traceback phase of the six-phase approach to service provider security, the action that occurs is tracing the attack flows from the attacked sections of the network toward the network edges. This phase entails identifying the source of the attack by analyzing the path that the attack traffic has taken through the network.

If RC is a stub router in an OSPF network, it requires a default route to be injected so that it can send traffic outside the OSPF domain. In OSPF, stub routers do not have any routes external to the OSPF domain in their routing tables. To allow these routers to reach networks outside of their OSPF domain, a default route should be injected into the stub area by the Area Border Router (ABR). This allows all routers in the stub area, including RC, to forward traffic for unknown destinations to the ABR, which then forwards it appropriately. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide

The correct configuration for MPLS LDP synchronization with OSPF process 1 on router R1 is to use the command mpls ldp igp sync holddown 60 under the OSPF process configuration. This ensures that the MPLS LDP synchronization is enabled and held for 60 seconds with OSPF process 1, which helps prevent black holes in MPLS networks during the convergence process by ensuring that routes are not advertised until LDP is fully operational and labels have been exchanged between adjacent routers.

References:

• Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - Cisco SPCOR
• Additional resources on Cisco’s Service Provider training: Cisco Service Provider Training

The issue of the OSPF domain receiving only the 172.17.1.0/24 route and not the default route 0.0.0.0/0 can be resolved by configuring OSPF to propagate default routes. Let’s take a look at the options:

• Option A: The configuration includes the following commands:
• router ospf 1
• default-information originate
• end

This configuration generates a default route into the OSPF domain, which is missing in this scenario.

The command “show policy-map control-plane” is used to display the control plane policies applied on a Cisco device, including the statistics related to packets matched by the class-maps of the policy-map. In this context, it helps in troubleshooting by providing detailed insights into how different types of traffic are being processed and controlled as they pass through the control plane.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) official course materials available on Cisco’s website.

https://www.cisco.com/c/en/us/solutions/service-provider/mobile-internet/5g-transport/converged-5g-xhaul-transport.html#

 Implementing CSC VPN services for a new backbone carrier provides several benefits. Firstly, it maintains a single backbone network, which simplifies the VPN implementation to customers (A). This eliminates the need for each Level 2 carrier to create and maintain a separate backbone network, thus lowering maintenance costs and simplifying management operations. Secondly, it supports a scalable growth strategy that services multiple customers efficiently (D). The Level 1 carrier can use one backbone network to provide VPN and Internet services for multiple Level 2 carriers, increasing revenues and efficiency.

References: The benefits of implementing CSC VPN services are detailed in the Huawei IP Encyclopedia, which explains the Carrier’s Carrier (CSC) networking solution in BGP/MPLS IP VPN2.

To achieve the origination of a default route based on the condition of the application server being up, a route map policy needs to be applied. This policy should match the condition of the server’s status and then use the default-information originate command to originate the default route with the specified metric type and value on router RL.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - OSPF Route Map Policy section.

 Transport Layer Security (TLS) is essential for securing RESTCONF communications on network devices. TLS provides a secure channel with encryption, ensuring that the data exchanged between the client and server remains private and integral. For RESTCONF to utilize TLS, it requires proper certificates for authentication. These certificates confirm the identity of the devices involved in the communication, preventing man-in-the-middle attacks and unauthorized access2.

References := Programmability Configuration Guide, Cisco IOS XE Amsterdam 17.1.x - RESTCONF Protocol2.

Cisco MPLS TE uses OSPF extensions to allow for optimized transit between a headend router and a destination router by utilizing Opaque LSAs. Opaque LSAs allow for the calculation and establishment of unidirectional tunnels that are set according to the network constraint. The tunnels are built bidirectionally by utilizing Router LSAs, which share router link advertisements to each router within the MPLS environment. ASBR Summary LSAs are also used to share OSPF domain information so that the two routers know how to reach each other during tunnel setup. Furthermore, Network LSAs are used to share RSVP information which is necessary for setting up the tunnel between the two routers.

In this scenario, gRPC dial-out mode is being used for telemetry. The receiver with IP address 192.168.1.1 will be assigned one of the subscriptions and will manage the ASR. To configure this, the router needs to use the protocol tcp command. This ensures that telemetry data is streamed out over a TCP connection to the specified receiver. Other options (A, B, and D) are not relevant for this specific use case.

In OSPF, the election of the designated router (DR) and backup designated router (BDR) is based on the OSPF network type. The network types include:

• Broadcast: This is the default network type for Ethernet interfaces. In a broadcast network, OSPF elects a DR and BDR. All other routers become DROTHERs. To prevent the election of a DR/BDR, you can configure the interface as non-broadcast (NBMA) using the ip ospf network non-broadcast command.
• Point-to-Point: This network type is used for point-to-point links (e.g., serial links). There is no DR/BDR election in point-to-point networks.
• Point-to-Multipoint: This network type is used for point-to-multipoint links (e.g., Frame Relay). There is no DR/BDR election in point-to-multipoint networks.
• Point-to-Multipoint Non-Broadcast: Similar to point-to-multipoint, but explicitly configured as non-broadcast. There is no DR/BDR election in point-to-multipoint non-broadcast networks.
• Loopback: Loopback interfaces are always treated as point-to-point.
• Virtual-Link: Used for OSPF virtual links.
• Sham-Link: Used for OSPF sham links.
• Demand Circuit: Used for demand circuits (e.g., ISDN).
• Non-Broadcast: Explicitly configured as non-broadcast. There is no DR/BDR election in non-broadcast networks.

References:

• Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) v1.0
• Cisco Learning Network Store - SPCOR Training

 The BFD (Bidirectional Forwarding Detection) interval configuration on an interface is automatically disconnected when the BFD-configured subinterface is removed. This is because BFD sessions are tied to the specific subinterface, and removing it will terminate the BFD session associated with that subinterface.

References: The information is based on the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course, which covers the configuration, verification, troubleshooting, and optimization of Service Provider IP network infrastructures, including BFD implementation

The issue here is that R1 and R2 cannot yet establish an LDP TCP connection. From the exhibit, it’s clear that the password is not required as it states “Password: not required, none, in use”. So, option C “Configure the no mpls Idp password option 1 command on R2” would be the correct answer to allow the establishment of an LDP TCP connection without requiring a password. This aligns with Cisco’s guidelines on configuring MPLS LDP where passwords might not be necessary for establishing connections between routers.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - Cisco SPCOR

 In a Unified MPLS routing architecture with partitioned IGP domains, it is essential to ensure that the iBGP Labeled Unicast address families are correctly configured to facilitate the exchange of VPNv4 routes directly between PE routers. In this case, ABR R102 should be configured with the address family-level configuration depicted in Option A to support this architecture. This configuration ensures that R101 can peer with both R102 and R103, and similarly, R201 can peer with R202 and R203 using iBGP Labeled Unicast address families. References := Implementing and Operating Cisco Service Provider Network Core Technologies

The correct configuration for enabling BGP FlowSpec client function and installation of policies on all local interfaces is flowspec address-family ipv4 install interface-all local. This command configures the router to accept FlowSpec policies from a BGP peer and apply them to all local interfaces. The flowspec keyword enables the BGP FlowSpec client function, address-family ipv4 specifies the address family, and install interface-all local ensures that the policies are installed on all local interfaces. References := Implementing and Operating Cisco Service Provider Network Core Technologies course.

To avoid advertising the same routes back to their sources when using RIP as the routing protocol between multiple PEs and CEs, the network engineer should define VRFs (Virtual Routing and Forwarding) on each device. VRFs allow for traffic separation by creating separate routing tables for different VPNs or customers. By using VRFs, each CE-PE link can be associated with a specific VRF, ensuring that routes are not inadvertently advertised back to their sources. Other options (A, B, and D) are not directly related to this specific requirement. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide.

The IPv4 address family configuration under neighbor configuration-mode must be removed. The exhibit shows the configuration of a BGP neighborship between an ASBR and a directly connected BGP speaker. The ASBR is running Cisco IOS XR. The neighbor is configured with the IPv4 address family, which is not supported on Cisco IOS XR. To establish the BGP neighborship, the IPv4 address family configuration must be removed.

https://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r41/routing/configuration/guide/routing_cg41xr12k_chapter1.html

 The configuration in the exhibit shows that R1 is configured with “mpls ldp graceful-restart”, which enables LDP Graceful Restart on the router. This means that R1 can support a graceful restart operation on the peer, even if graceful restart is disabled on the peer. This feature allows LDP to recover from failures without affecting the forwarding plane, ensuring network stability and minimal packet loss during failovers.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - Cisco SPCOR Training & Certification

 Router R1 is configured as a stub area with the “no-summary” option, which means it will not receive summary LSAs (Type 3) from the Area Border Router (ABR). It will only have Type 1 (Router LSAs) and Type 2 (Network LSAs) in its OSPF database for the area it belongs to. Router R2 is configured as an NSSA (Not So Stubby Area), which allows it to import AS external routes as Type-7 LSAs. These Type-7 LSAs can then be converted to Type-5 LSAs by the ABR when propagated into other areas. Therefore, R2 has Types 1, 2, and 7 LSAs in its OSPF database.

References: For more detailed information, please refer to the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials, specifically the sections covering OSPF area types and LSA types.

https://www.cisco.com/c/en/us/td/docs/ios/12_2sr/12_2sra/feature/guide/srtunsel.html#wp105781 5

The configuration shown in the exhibit indicates that Router 1 is configured with NETCONF-YANG and has enabled the feature candidate-datastore. This means that Router 1 has a temporary data store where a copy of the running configuration can be manipulated and verified before committing the configuration. This allows administrators to test changes before applying them to the running configuration, reducing the risk of errors that could impact network operations.

References: = Implementing and Operating Cisco Service Provider Network Core Technologies course materials. 

 A Multi-Layer control plane, like Cisco’s nLight technology, provides an integrated approach that allows for the automatic provisioning, monitoring, and management of traffic across different network layers, from Layer 0 (optical) to Layer 3 (IP). This integration increases network agility and flexibility while improving network utilization, leading to significant cost savings and more efficient network resiliency solutions2.

References: The Economics of Cisco’s nLight Multilayer Control Plane Architecture2.

 To meet the scalability and service recovery requirements, the network engineer should implement BGP PIC core functionality on routers R2 and R3 (Option A). This will enhance the convergence time during a failure. Additionally, establishing BGP connectivity between routers R1 and R4 with VPNv4 address family enabled (Option C) will facilitate MPLS services across multiple IGP domains.

References :=

• Implementing and Operating Cisco Service Provider Network Core Technologies
• On-Demand E-Learning for Implementing and Operating Cisco Service Provider Network Core Technologies

 Unicast Reverse Path Forwarding (uRPF) in strict mode ensures that packets are received on the interface that the router would use to forward the return traffic. If a packet is received on an interface that is not the best reverse path, the packet is dropped. This helps mitigate IP address spoofing and DDoS attacks.

 The error message “%CLNS-4-AUTH_FAIL: ISIS: LAN LIIH authentication failed” indicates that there is an authentication failure in the IS-IS routing protocol between routers R1 and R2. In the exhibit, it can be observed that R2 has a state of “UP” for its IS-IS neighbor relationship, while R1 is in “INIT” state. This discrepancy in states indicates an issue with the establishment of the neighbor relationship, which can be attributed to an authentication failure at both Level 1 and Level 2 PDUs as indicated by option B.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) official guide or documentation available on Cisco’s official website.

The keyword ‘none’ is essential in management plane security using TACACS to ensure that authentication can still succeed when the TACACS+ server is unreachable. This fallback mechanism allows network resources to remain accessible even if the TACACS+ server fails or becomes unreachable. References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - Management Plane Security section.

1: PIM-DM 2:IGMP 3:PIM-SM 3:shared tree 4:source tree

Option D is the correct answer because, in the context of Auto-RP, sparse-dense mode allows the router to forward Auto-RP messages. Auto-RP uses dense mode multicast groups (224.0.1.39 and 224.0.1.40) to advertise RP mapping information, so enabling sparse-dense mode on the interface ensures that it can process both types of multicast traffic. References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) official course materials, which can be found here.

The script in the exhibit is for configuring a static VLAN (Option D). The XML configuration specifies a static VLAN range with “allocMode=‘static’”, indicating that VLAN IDs are assigned manually, not dynamically.

References := These explanations are derived from the concepts outlined in the Cisco Service Provider source book, specifically the “Implementing and Operating Cisco Service Provider Network Core Technologies” course materials,

The script shown in the exhibit is a REST API call that adds a user with the last name ‘CiscoTest’ to the AAA database on the server located at the IP address 192.168.201.10. This is achieved through a POST request, which is typically used to create or update resources on a server. The script specifies the user details in JSON format, which is a common data format used for API calls.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)

R1

Router bgp 65515

No bgp default ipv4-unicast

Neig 2.2.2.2 remote-as 65516

Nei 2.2.2.2 update-soc loopback0

Nei 2.2.2.2 ebgp-multihop 2

Neig 2.2.2.2 pass C1sc0!

Nei 2000:cc13:cc13:2::1 remote-as 65516

Nei 2000:cc13:cc13:2::1 update-so loopback0

Nei 2000:cc13:cc13:2::1 pass C1sc0!

Nei 2000:cc13:cc13:2::1 ebgp-multihop 2

Address-family ipv4

Neig 2.2.2.2 activate

Address-family ipv6

Nei 2000:cc13:cc13:2::1 activate

Ip route 2.2.2.2 255.255.255.255 192.168.1.2

Ipv6 route 2000:cc13:cc13:2::1/128 2000:cc13:cc13:cc13::2

R2

Router bgp 65516

No bgp default ipv4-unicast

Neig 1.1.1.1 remote-as 65515

Nei 1.1.1.1 update-soc loopback0

Nei 1.1.1.1 pass C1sc0!

Nei 1.1.1.1 ebgp-multihop 2

Nei 2000:cc13:cc13:1::1 remote-as 65515

Nei 2000:cc13:cc13:1::1 update-so loopback0

Nei 2000:cc13:cc13:1::1 pass C1sc0!

Nei 2000:cc13:cc13:1::1 ebgp-multihop 2

Address-family ipv4

Neig 1.1.1.1 activate

Address-family ipv6

Nei 2000:cc13:cc13:1::1 activate

Ip route 1.1.1.1 255.255.255.255 192.168.1.1

Ipv6 route 2000:cc13:cc13:1::1/128 2000:cc13:cc13:cc13::1

When choosing between SaltStack and Chef for network automation, it is important to consider that Chef is an agent-based tool written in Ruby, while SaltStack is a Python-based module tool. This fundamental difference in language and architecture can influence the decision based on the existing environment and the team’s expertise.

References :=

• Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials.
• Official Cisco documentation and training resources available on the Cisco Learning Network Store.

R1

key chain AUTH_ISIS

key 2

key-string C1sco!

exit

int range et0/0 , et1/0

isis authen key-chain AUTH_ISIS

ip isis

isis metric 15

Copy run start

R2

key chain AUTH_ISIS

key 2

key-string C1sco!

exit

int range et0/0 , et1/0

isis authen key-chain AUTH_ISIS

ip isis

isis metric 20

Copy run start

R3

key chain AUTH_ISIS

key 2

key-string C1sco!

exit

int range et0/0 , et1/0

isis authen key-chain AUTH_ISIS

ip isis

isis metric 25

Copy run start

The configuration creates a class map named WEB which is used to match HTTP traffic. This class map can then be referenced in a policy map to define specific actions for traffic that matches the criteria, such as applying QoS policies or traffic shaping.

References: This concept is covered in the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course, where class maps and policy maps are discussed in the context of traffic classification and policy enforcement.

 The configuration in the exhibit shows the implementation of Nonstop Forwarding (NSF) with OSPF. NSF is used to minimize the downtime of neighbor relationships during a Route Processor (RP) switchover. The nsf command enables NSF, and ietf specifies the use of the IETF standard for graceful restart in OSPF. The restart interval 90 sets the time, in seconds, within which the restarting router should complete its restart, helping to maintain uninterrupted forwarding despite the switchover.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR v1.0); Cisco SPCOR Training & Certification.

 To establish LDP peering with the loopback IP address as its Router ID, both RA and RC need to configure their LDP router IDs to use their respective loopback addresses. This is done by applying the ‘mpls ldp router-id loopback0’ command on both routers. This configuration ensures that LDP peering uses the loopback addresses, which is a requirement for the service-provider core network.

References := This explanation is based on the concepts outlined in Cisco’s Implementing and Operating Service Provider Network Core Technologies (SPCOR) course, which provides in-depth knowledge on service provider infrastructure. For further study, refer to the official Cisco documentation and training materials available on the Cisco Learning Network Store.

 The number “2” in the SNMP server configuration “snmp-server community ciscotest ro 2” refers to the numeric name of the Access Control List (ACL) that contains the list of SNMP managers with access to the agent. In this context, “ro” stands for read-only access, meaning that SNMP managers can only read but not modify data on the device. The ACL identified by number “2” specifies which SNMP managers are authorized to access SNMP data on this device using the community string “ciscotest”.

References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide.

Application, table Description automatically generated with medium confidence

YANG (Yet Another Next Generation) is a data modeling language used primarily for the configuration and state data of network elements. It is closely associated with the NETCONF (Network Configuration Protocol) for which it models configuration data. YANG provides schemas that define how data is structured and transported by NETCONF operations. It also shapes the state data of network elements, allowing for a standardized format for representing the operational state of devices. References: YANG is defined in RFCs such as RFC 6020 and RFC 7950, which outline its role in NETCONF operations and its capabilities in modeling both configuration and state data.

The configuration snippet in the exhibit shows that BGP summarization is configured with the “aggregate-address” command followed by an IP address and a subnet mask, and then the “summary-only” and “as-set” options. The IP address is 192.168.0.0, and the subnet mask is 255.255.0.0, which corresponds to a /16 prefix length (indicating that the first 16 bits of the IP address are the network portion). However, there seems to be a typo in option B as it’s not a valid IP address format; hence option A is correct with an assumption of typo error.

References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide

The configuration shown in the exhibit enables IP flow information collection on the interface gigabitethernet0/1. This setup is used for network traffic analysis, and when applied, it provides data that includes the source interface of the traffic for traceback analysis. This is useful for identifying the origin of traffic, which can be critical in situations such as security incidents or network troubleshooting.

References: The details for this configuration can be found in the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials, which serve as a comprehensive guide for understanding and applying Cisco service provider technologies.

The correct configuration for extending the layer 2 domain between the company’s two locations involves setting up the interface with L2 transport, specifying the encapsulation method as dot1q with the VLAN tag of 12, and applying the appropriate rewrite ingress tag rules. This setup ensures that the VLAN tag is preserved across the service provider’s core, maintaining the layer 2 domain continuity.

References := Implementing and Operating Cisco Service Provider Network Core Technologies

• References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide.

Cisco MPLS Traffic Engineering (TE) tunnels necessitate a link-state routing protocol like OSPF or IS-IS because these protocols use Shortest Path First (SPF) calculations. The tunnel endpoints leverage these SPF calculations to implement the tunnel, ensuring an efficient and optimized path through the network. This is essential for MPLS TE, which aims to optimize network resource utilization and improve traffic distribution across the network.

References: Cisco Community, Cisco Documentation

 QPPB (QoS Policy Propagation via BGP) is a mechanism that allows the application of QoS policies using IP precedence or QoS group settings based on BGP community lists, AS paths, and prefix lists. In the context of the exhibit provided, it’s clear that QPPB is being used to apply a specific QoS policy (qos-group 10) based on AS path attributes. This aligns with option C, as it indicates that QoS policies are utilizing BGP to achieve comprehensive network coverage.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR v1.0); Cisco SPCOR Training

In Cisco’s path selection process, the weight attribute is the first criterion for selecting a path. It is a Cisco-specific parameter, local to the router, and it is not propagated in routing updates. The path with the highest weight is preferred. Therefore, configuring a high weight on the peer to ASN 4567 will make Router R1 prefer this path for all outbound traffic directed towards ASN 4567. References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - Cisco SPCOR Training & Certification

 ISP delegation to PCE servers involves assigning specific tasks or roles to different PCE servers within a network. Option A refers to adding a new PCE server with lower precedence than the primary PCE, which means introducing an additional server that has less priority in task execution compared to the existing primary one. Option B involves changing the precedence of any of the PCE servers, indicating a modification in their hierarchical order or priority for task execution. References := Cisco Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)

IS-IS uses NET addresses to identify each router in the network, and the NET address of each router must be unique. In order for IS-IS to establish connectivity between R1 and R3, the NET address of R3 must be different from the NET address of R1, but it must also follow the same structure. In this case, the NET address of R1 is 49.0133.532b.ca14.6915.21311.F40F.1B3a.ba10.00, so the NET address of R3 must be 49.0133.532b.ca14.6915.21311.F40F.1B4a.bb87.00.

• The configuration in Option A is used to implement URPF in loose mode on the GigabitEthernet0/1 interface.
• Loose mode allows the router to check for any route back to the source, not necessarily the best route.
• By enabling URPF, the router ensures that incoming packets have a valid return path in the routing table.
• This helps prevent IP spoofing and limits malicious traffic on the network.

References:

• Implementing and Operating Cisco Service Provider Network Core Technologies
• On-Demand E-Learning

The failure to implement IS-IS multitopology can be attributed to the routing process not supporting extended metrics. Extended metrics are necessary for multitopology routing because they allow for the definition of multiple topologies within the same routing protocol, each with its own set of metrics and paths1.

References:

• Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) source documents or study guide

 In XML, a self-closing tag such as  indicates that the element does not contain any data, hence the data field is considered blank. This is a common way to represent empty elements in XML documents.

References: For further details, you can refer to XML-related sections in the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) materials, which explain the structure and usage of XML in network configurations.

This configuration sets up policing rules for different protocols including CDP (Cisco Discovery Protocol) and ARP (Address Resolution Protocol), with specific rate limits for invalid packets as well as CDP and ARP protocols. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide

The Adjacency-SID sub-TLV extension is advertised within TLV-22 (Extended IS Reachability) to label a specific link in a segment routing domain. This allows for the identification and utilization of specific paths or links within the network, facilitating more efficient routing and traffic management. References := Implementing and Operating Cisco Service Provider Network Core Technologies

 In this scenario, BGP is used in the core of the service provider network, while OSPF serves as the PE-CE routing protocol. To ensure communication between CE1 and CE2, which are located in different geographical locations, it’s essential for PE1 and PE2 to share routes. This can be achieved by configuring both PEs to mutually redistribute BGP and OSPF routes within the VRF dedicated for that customer, ensuring seamless communication between both customer endpoints. References: Implementing and Operating Cisco Service Provider Network Core Technologies

 Both options provide a default route pointing to CE-1, allowing CE-2 to access the internet. The specific choice would depend on additional context or requirements not provided in the question.

References:

• Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) study materials.

Cisco MPLS TE (Traffic Engineering) tunnels provide a way to optimize traffic routing within an MPLS network. However, there are certain constraints to be aware of:

• QoS-aware tunneling: Unfortunately, Cisco MPLS TE tunnels do not inherently support Quality of Service (QoS) awareness. This means that the tunnels themselves do not directly consider QoS parameters when making routing decisions. QoS policies must be applied separately at the network level, and the TE tunnels do not inherently take QoS into account during path selection.
• Tunnels spanning multiple OSPF areas: Contrary to option A, Cisco MPLS TE tunnels can indeed span multiple OSPF areas. The use of OSPF areas does not inherently restrict the creation of MPLS TE tunnels across area boundaries.
• ISIS metrics: Option B is incorrect. When using ISIS (Intermediate System to Intermediate System) as the Interior Gateway Protocol (IGP), newer-style metrics (such as wide metrics) are supported. Older-style metrics are not the only option.
• Tunnels over IP unnumbered links: Option C is also incorrect. Cisco MPLS TE tunnels can be configured over IP unnumbered links, allowing efficient use of IP addresses.

In summary, the primary constraint is the lack of built-in QoS awareness within MPLS TE tunnels.

References:

• Implementing an MPLS VPN over TE Tunnels - Cisco Support
• Configuring Basic MPLS TE - Cisco NX-OS

 To establish MPLS LDP sessions between two routers, both routers must be configured to support MPLS on the interfaces that connect them. The configuration shown for R2 includes enabling MPLS label protocol LDP and configuring interfaces Ethernet1/0 and Ethernet1/1. However, to complete the MPLS LDP session setup, R2 also needs to have MPLS enabled on the interface toward R1. This is done by entering the interface configuration mode for the relevant interface and using the mpls ip command. This command enables MPLS forwarding for IP packets on the interface, which is necessary for LDP to advertise and map labels to the IP routes.

References := The answer is based on the concepts covered in the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course,

The configuration ip verify unicast source reachable-via any under interface gigabitethernet0/1 on Router 1 ensures that incoming packets have a source IP address that matches an entry in the FIB (Forwarding Information Base), indicating it’s reachable via a real interface. This helps mitigate attacks by dropping traffic with unreachable source addresses. References := Cisco

IOS XE:

It uses linux-based kernel

It has a separate control plane

IOS:

It is monolithic

It shares memory space

 To align with customer contract SLAs and allow 10% of interface capacity on router R3 for traffic from CE1 towards the FTP server, the network engineer must apply a policy map to R1 to reserve the remaining 10% of interface bandwidth (Option C). Additionally, applying a policy map to R3 to reserve 10% of interface bandwidth (Option D) ensures adherence to the customer’s contract SLAs while utilizing the allocated bandwidth capacity. References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - Quality of Service section.

The task requires the use of BGP’s well-known discretionary attribute to select the preferred path, excluding FTP prefixes from this selection process. Option B is correct because it applies a route map to incoming routes from a specific neighbor, which can be used to set attributes like local preference or AS path, or filter routes based on prefix lists or access lists.

The configuration snippet shows a route map named “ciscotest” that sets the local preference to 200 for routes matching IP address 1 (presumably defined elsewhere in an access list or prefix list). Local preference is a well-known discretionary attribute in BGP that influences path selection within an autonomous system; higher values are preferred.

References := Cisco - Implementing and Operating Cisco Service Provider Network Core Technologies

In the Pipe model of MPLS QoS, the MPLS EXP bits are set by the Customer Edge (CE) device. This model allows the CE to mark the packets, and these markings are retained throughout the MPLS network until they reach the egress Provider Edge (PE) router. The PE router does not alter the MPLS EXP value, ensuring that the QoS policy applied by the customer is preserved end-to-end.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR)

Segment routing prefix segments are linked to a prefix SID that is globally unique within the segment routing domain. This means that each prefix SID identifies a specific prefix in the network and is unique across the entire segment routing-enabled domain, ensuring that the path to the prefix can be identified and used by any node within the domain1. References: Introduction to Segment Routing - Cisco Learning Network2, ASR9000/XR Introduction to Segment Routing - Cisco Community3, About Segment Routing - Cisco Content Hub

Ansible is widely recognized as a robust network automation tool that facilitates provisioning, configuration, and management of network devices. It uses simple, human-readable YAML syntax for its playbooks, making it easy to define tasks and orchestrate workflows for automated network operations1.

The URL in the exhibit is used with REST API to send a message to the APIC (Application Policy Infrastructure Controller) to perform an operation on a managed object or class operator. In Cisco’s ACI (Application Centric Infrastructure), REST API requests are used for managing, configuring, and retrieving data from the APIC. The URL structure typically includes the IP address of the APIC and specific paths that refer to objects or classes within the ACI fabric. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide

To enable LDP session protection for LDP neighbors within each VRF, the engineer should configure LDP session protection within the individual VRFs. This ensures that LDP sessions are protected at the VRF level, providing security and stability for MPLS-based services. By enabling LDP session protection within each VRF, the router will take appropriate actions to protect LDP sessions against misbehaving neighbors or potential attacks. References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) v1.0

MPLS LSP ping is a utility for locating faults within an MPLS network, specifically for Label Switched Paths (LSPs). It helps in verifying the LSPs in the MPLS network. The utility sends echo requests to the destination, and if the path is complete, echo replies are received. References := Cisco

Remember that SSM is an extension of IP multicast where datagram traffic is forwarded only from explicitly joined multicast sources to receivers. It creates source-specific multicast distribution trees without shared trees.

References:

• Cisco PIM-SSM Configuration Example
• Cisco IP Multicast: PIM Configuration Guide

The PSID plays a crucial role in segment routing, allowing efficient forwarding of packets along predefined paths.

For more detailed information, please refer to the official Cisco documentation on Segment Routing and IPv6. Unfortunately, I cannot directly cite specific pages from the provided resources, but you can find relevant details in the Cisco documentation.

 The configuration sets up a telemetry subscription to collect and send data every 60 seconds, which is indicated by the sample-interval 60000 setting in the configuration. References: For more detailed information, please refer to the official Cisco documentation on Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) and the specific section on Telemetry Configuration.

Best – 50.50.50.2

2nd Best – 40.40.40.2

3rd Best – 20.20.20.2

44th Best – 30.30.30.2

 In the context of Cisco IOS XR software, the configuration under Option D is appropriate for adding an interface to a bundle using LACP (Link Aggregation Control Protocol). The configuration specifies two Ten Gigabit Ethernet interfaces (TenGigE0/1/0/5 and TenGigE0/1/0/6) with descriptions indicating they are part of “bundle_1_link”. Both interfaces are assigned to “bundle id 1” with a load interval of 30 seconds, ensuring they are part of the same link aggregation group and share traffic load.

In an MPLS network, the Label Distribution Protocol (LDP) is used to distribute labels which can include segment prefixes. LDP is a protocol that automatically generates and exchanges labels between routers, allowing for the forwarding of packets along a predetermined path without the need for complex lookups in a routing table at every hop.

References: Segment Routing Overview and Migration Guidelines - Cisco1.

 In OSPF, the election of the designated router (DR) and backup designated router (BDR) is based on the OSPF network type. The network types include:

• Broadcast: This is the default network type for Ethernet interfaces. In a broadcast network, OSPF elects a DR and BDR. All other routers become DROTHERs. To prevent the election of a DR/BDR, you can configure the interface as non-broadcast (NBMA) using the ip ospf network non-broadcast command.
• Point-to-Point: This network type is used for point-to-point links (e.g., serial links). There is no DR/BDR election in point-to-point networks.
• Point-to-Multipoint: This network type is used for point-to-multipoint links (e.g., Frame Relay). There is no DR/BDR election in point-to-multipoint networks.
• Point-to-Multipoint Non-Broadcast: Similar to point-to-multipoint, but explicitly configured as non-broadcast. There is no DR/BDR election in point-to-multipoint non-broadcast networks.
• Loopback: Loopback interfaces are always treated as point-to-point.
• Virtual-Link: Used for OSPF virtual links.
• Sham-Link: Used for OSPF sham links.
• Demand Circuit: Used for demand circuits (e.g., ISDN).
• Non-Broadcast: Explicitly configured as non-broadcast. There is no DR/BDR election in non-broadcast networks.

References:

• Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) v1.0

R1

router ospf 10

redistribute static

int et0/0

ip ospf hello-interval 5

ip ospf dead-interval 10

ip ospf cost 15

ip ospf 10 area 0

copy run start

R2

router ospf 10

redistribute static

int et0/0

ip ospf hello-interval 5

ip ospf dead-interval 10

ip ospf cost 15

ip ospf 10 area 0

copy run start

The correct configuration to ensure that SNMP servers acknowledge the notifications they receive is to use the snmp-server host command with the Informs keyword. This configuration sends Inform requests instead of Trap messages. Unlike Traps, Inform requests are acknowledged by the receiving SNMP server, ensuring that the notification has been received. If an Inform request is not acknowledged, the SNMP agent resends the notification.

References: The information is based on the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) training, which teaches how to configure, verify, troubleshoot, and optimize next-generation, Service Provider IP network infrastructures.

In the context of OSPF multiarea implementation, adjacency issues can often be resolved by specifying the type of network on the interface. In this case, option B “ip ospf network point-to-point” is appropriate as it helps in forming OSPF adjacency over point-to-point links by allowing OSPF to use a simpler neighbor discovery process, which can resolve adjacency issues. References := Implementing and Operating Cisco Service Provider Network Core Technologies

 The number 2 in the configuration “snmp-server community ciscotest ro 2” is significant because it refers to the numeric name of the Access Control List (ACL) that contains the list of SNMP managers with access to the agent. In this context, “ro” stands for read-only, meaning that SNMP managers listed in ACL 2 can only read data from the SNMP agent but cannot modify it. The ACL defines which IP addresses are allowed to access SNMP data. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide

 MPLS LDP (Label Distribution Protocol) is used for label distribution in MPLS networks. When making changes to the LDP configuration, it’s essential to ensure that the changes do not disrupt existing LDP sessions. In this scenario, the network administrator implemented MPLS LDP changes on the PE-A LSR (Label Switching Router) device, and the goal is to prevent any disruption to LDP peers.

The MPLS LDP Non-Stop Routing (NSR) feature allows LDP sessions to survive control-plane switchover events without interruption. When NSR is enabled, the LDP session state information is synchronized between the active and standby control planes. If the active control plane fails, the standby control plane takes over seamlessly, and LDP sessions continue without interruption.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/msp/configuration/xe-3s/mp-ha-xe-3s-book/mp-nsr-ldp-supp.pdf

Model-driven telemetry (MDT) utilizes YANG models to enable the subscription to specific data items that are streamed from network devices. This allows applications to receive near real-time updates without the need for traditional polling methods. MDT with YANG provides a more efficient and scalable way to monitor network devices by pushing updates to subscribers, which can specify the exact data they require2.

References: Configure Model-driven Telemetry on Cisco IOS-XE Devices with YANG Suite - Cisco2.

The command “traceroute mpls ipv4 10.20.0.1/32 ttl 4” is used to trace the route that packets take to get from the source to the destination in an MPLS network, specifically for IPv4 addresses with a maximum of 4 hops (Time To Live). This command will provide information on all labels and hop-by-hop IP addresses for the specified destinations, meeting the requirements stated in the question.

References := For more detailed information, you can refer to the Implementing and Operating Cisco Service Provider Network Core Technologies training, which covers the configuration, verification, troubleshooting, and optimization of Service Provider IP network infrastructures, including MPLS operations

• To prevent packet loss when IGP (Interior Gateway Protocol) and LDP (Label Distribution Protocol) are not synchronized, enabling MPLS LDP IGP synchronization is crucial. This synchronization ensures that the IGP routing protocol (such as OSPF or IS-IS) waits until LDP convergence is completed before advertising labels for MPLS traffic. It helps maintain consistency between the IGP and LDP databases.
• References: Implementing and Operating Cisco Service Provider Network Core Technologies course materials.

 NSO, or Network Services Orchestrator, provides full lifecycle management of devices and services in a network. It is designed to automate the service lifecycle from design and creation through deployment and decommissioning, without the need for manual intervention. This includes configuration, activation, updating, and ultimately, removal of services.

References: The role of NSO is detailed in the Cisco Crosswork Network Services Orchestrator (NSO) documentation

 In a gRPC dial-in configuration, the encoding is specified by the client initiating the connection. This setup allows for connection multiplexing, which means multiple gRPC calls can be made concurrently over a single connection, improving efficiency. Two-way streaming is also facilitated, allowing both the client and server to send a sequence of messages to each other, providing a full-duplex communication channel.

The Internet gateway router being connected as a PE router to the MPLS backbone is a design attribute that can be used to provide Internet access to a major customer through a separate dedicated VPN. This setup allows for efficient routing and separation of traffic, ensuring security and performance.

 For OSPF, the subnet mask must match between two devices on the same network segment to form an adjacency, as it defines the network’s address range. The hello timer setting is crucial for the OSPF Hello protocol, which is used for neighbor discovery and maintaining neighbor relationships. Finally, the area number must be the same because OSPF uses areas to define a hierarchy within the network, and routers within the same area share routing information.

References: OSPF is a link-state protocol that requires certain parameters to match for a successful adjacency. This includes the subnet mask, hello timer, and area number, which are fundamental to OSPF’s operation and ensure that routers can communicate effectively within the same area

PCE – 1,2,5

PCC- 3,4